Taipan Laminate airgunUragans airgun

Complete Oring List

Home Forums BullPups EdGun Complete Oring List

This topic contains 64 replies, has 26 voices, and was last updated by  airbrained 11 months, 4 weeks ago.

Viewing 15 posts - 16 through 30 (of 65 total)
  • Author
    Posts
  • #119955

    dvu0704
    Member

    Hoot,

    I think you’re mixed up with the Lelya, Veles does not cost $1,300.00 and Veles may not be available in .22 cal yet.

    #120012

    toshik
    Member
    quote dvu0704:

    Hoot,
    I think you’re mixed up with the Lelya, Veles does not cost $1,300.00 and Veles may not be available in .22 cal yet.

    Let me clarify this: the latest shipment of Lelyas came in .22
    I also have one new .22 Veles for sale.
    Both of them can be ordered in .177 as well.

    #120016

    hoot
    Participant
    quote toshik:

    quote dvu0704:

    Hoot,
    I think you’re mixed up with the Lelya, Veles does not cost $1,300.00 and Veles may not be available in .22 cal yet.

    Let me clarify this: the latest shipment of Lelyas came in .22
    I also have one new .22 Veles for sale.
    Both of them can be ordered in .177 as well.

    Never again doubt your elders….boy!

    Regards,
    Mo’ Hoot (where’s my Black emoticon? Don’t be violating my civil rights!)

    #121748

    Tag. Thanks!

    Paul

    #131020
    quote toshik:

    They are as follows:
    • Ф 25 х 3 – 4 pcs (front and rear plugs, regulator)
    • Ф 2,57 х 1,78 – 1 pcs (front plug filling valve)
    • Ф 5 х 1,5 – 3 pcs (front of the regulator shaft) – 1, inside the regulator – 1, bottom of the bolt assembly -1)
    • Ф 8 х 1.5 – 1 pcs (rear of the regulator shaft)
    • Ф 7 х 1.5 – 1 pcs (rear of the barrel seal), .177 uses Ф5х1,5)
    • Ф 12 х 2,5 – 1pcs (permanent compensator seal)
    • Ф 3 х 1; 2.5 х 1,02 – 2 pcs (pellet probe for .22 or .177)
    • Ф 5 х 1,5 – 2 pcs for the filling probe

    Forgive my ignorance but when looking at this list,

    25×3 – 25mm is the inside diameter and 3mm is the cross section?

    Thanks

    Paul

    #141376

    toshik
    Member
    quote libertyman777:

    Forgive my ignorance but when looking at this list, 25×3 – 25mm is the inside diameter and 3mm is the cross section?
    Thanks
    Paul

    Correct!

    #175371

    hemn
    Member

    Dears;

    Dose anybody can tell us, which type of o-rings they are made from? i mean they are from Buna or Viton, and which Duro 90 or 75 or 70….?? !!
    Could you please be more clear?

    I cannot find above mentioned sizes in this site;

    http://www.theoringstore.com/index.php?main_page=product_info&products_id=3624

    your help would highly appreciated.

    #202482

    toshik
    Member

    R3M o-rings list:
    • Ф 2,57 х 1,78 – 1 pcs (front plug filling valve)
    • Ф 5.1 х 1.6/6 x 1.6 – 1 pcs (pellet probe for .22/.25)
    • Ф 5 х 1.5 – 5 pcs (front of the regulator shaft – 1, inside the regulator – 1, seal between the tank and bolt assembly on .22 only -1, filling probe – 2)
    • Ф 8 х 1.5 – 1 pcs (rear of the regulator shaft)
    • Ф 19 х 2 – 1 pcs (permanent compensator seal)
    • Ф 25 х 3 – 4 pcs (front and rear plugs, regulator)
    • Ф 22 х 1.5 – 4 pcs (2 multishot clips)
    • Ф 5 х 2.5 – 1 pcs (pressure gage)

    #202531

    wanta-edgun
    Member

    The burna 70 is fine for just about everything. If want to use something stronger for the probe orings, try the burna 90, the viton 75(not much stronger) or the urethane 70 or 90. However, I have heard that some guns don’t like the 90 dur uratane. They are cheap enough, just get a few of each in each type you can so your not left without if one type doesn’t work.

    #202991

    Hi Old Goat,

    I owe you one set of Orings. It just came in. I will send them in a few days. Did you thought I forgot about you?

    John.

    #203004

    merou
    Member

    Hi all, we have well all the information of the size of O’rings for different model of Edgun.
    It would be possible for somebody to make one or several plans with names and size and locations of the various references of joints.
    From these lists as reference point.

    • Ф 25 х 3 – 4 pcs (front and rear plugs, regulator)
    • Ф 2,57 х 1,78 – 1 pcs (front plug filling valve)
    • Ф 5 х 1,5 – 3 pcs (front of the regulator shaft) – 1, inside the regulator – 1, bottom of the bolt assembly -1)
    • Ф 8 х 1.5 – 1 pcs (rear of the regulator shaft)
    • Ф 7 х 1.5 – 1 pcs (rear of the barrel seal), .177 uses Ф5х1,5)
    • Ф 12 х 2,5 – 1pcs (permanent compensator seal)
    • Ф 3 х 1; 2.5 х 1,02 – 2 pcs (pellet probe for .22 or .177)
    • Ф 5 х 1,5 – 2 pcs for the filling probe

    R3M o-rings list:
    • Ф 2,57 х 1,78 – 1 pcs (front plug filling valve)
    • Ф 5.1 х 1.6/6 x 1.6 – 1 pcs (pellet probe for .22/.25)
    • Ф 5 х 1.5 – 5 pcs (front of the regulator shaft – 1, inside the regulator – 1, seal between the tank and bolt assembly on .22 only -1, filling probe – 2)
    • Ф 8 х 1.5 – 1 pcs (rear of the regulator shaft)
    • Ф 19 х 2 – 1 pcs (permanent compensator seal)
    • Ф 25 х 3 – 4 pcs (front and rear plugs, regulator)
    • Ф 22 х 1.5 – 4 pcs (2 multishot clips)
    • Ф 5 х 2.5 – 1 pcs (pressure gage)

    The burna 70 is fine for just about everything. If want to use something stronger for the probe orings, try the burna 90, the viton 75(not much stronger) or the urethane 70 or 90. However, I have heard that some guns don’t like the 90 dur uratane. They are cheap enough, just get a few of each in each type you can so your not left without if one type doesn’t work.

    Re: OldGoat, Nice & Helpful guy….
    by oldgoat » Wed Oct 02, 2013 10:17 am
    Hello Hemn, thanks for the kind words!

    I don’t have any O ring kits left and I don’t plan on offering another group buy. The last group buy got way out of hand and I needed to count, sort, bag and ship 7,800 O rings.
    Each kit contained 380 O rings.
    A little info on the terms 70-90 Duro and Buna N. Duro is a hardness rating, 90 is harder than 70. Buna N is the standard composition of a basic O ring. If the O ring isn’t listed as something else, it is almost certainly Buna N and should be around 70 Duro hardness.
    I started the buys because the early R2.5 Matadors would wear out the bolt probe O rings very quickly. I finally found a source for harder 90 Duro Buna N, O rings and the harder O rings last a whole lot longer.
    I think that Ed has started using harder O rings on the bolt probe as nobody seems to have a problem with the current R3s leaking at the cocking handle probe.
    Here is the complete list for all of the Matadors, R2.5, R3 and R3M in .177, .22 and .25 cal. The first number is mm ID and the second number is mm thickness/cross section.

    2.5 x 1.75 Buna 70 front barrel plug fill O ring seal
    2.5 x 1.02 Buna 90 .177 cocking handle probe O rings
    3 x 1 Buna 90 .22 cal cocking handle probe O rings
    4 x 1 Buna 90 .25 cal cocking handle probe O rings
    5 x 1.5 Buna 70 regulator shaft, fill probe
    8 x 1.5 Buna 70 regulator shaft
    25 x 3 Buna 70 regulator/air valve housing, front air tube plug
    20 x 1 Buna 90 baffle
    7 x 1.5 Buna 70 breech end of barrel R2.5s
    12 x 2.5 Buna 70 barrel seal inside rear moderator tube

    The kits were overkill but; I would recommend that you buy a few sets of the 90 Duro Buna N, O rings for the cocking handle probe and a couple of the 90 Duro Buna N, O rings for the baffle. The baffle O rings can easily get wore/torn if you remove the front baffle tube very often. 90 Duro ones will last a lot longer there.

    You will probably have to order the 90 Duro O rings, I would be very surprised if you can find them locally.

    Stay with 70 Duro Buna N for the rest of the O rings. You might want to pick up a couple each of the 2 regulator shaft O rings and a few of the regulator/air valve housing O rings also. I wore the regulator shaft O rings out after 15,000-17,000 shots. The cocking bolt probe, fill probe, regulator shaft and, if you remove the reg, the reg/air valve housing, O rings are the only O rings that are subjected to wear, the rest should last indefinitely.

    You might want to buy a few 5 x 1.5 O rings for the fill probe also although, the original O rings that came on my R2.5s fill probe are still going strong after almost 5 years. I still use the original probe to fill all of my Matadors.

    You also need to order at least one extra air valve rod. NOW! You will eventually break one and you will be very happy that you have an extra when you need it!

    Re: OldGoat, Nice & Helpful guy….
    by Veerkracht » Fri Oct 11, 2013 2:13 pm
    oldgoat wrote:Hi Hemn.
    The O ring list that I posted here is the correct one.
    Hi Tedd,
    Thanks for the info!
    I´ve got just one silly question left:
    The o-ring: 5 x 1.5 Buna 70 regulator shaft, fill probe
    Am I correct in assuming that the regulator setting screw is the same size?

    ( The photo which I puts it is just an example to give ideas)

    Thank you for your Help.

    MIKA

    #203384

    veerkracht
    Member

    Hi Mika,

    You are doing a lot of work, thanks!

    In Tedd’s list there is a:
    20 x 1 Buna 90 baffle
    I think this should be the
    19 х 2 – 1 pcs (permanent compensator seal)
    in your list?

    Regards, Robert.

    #203525

    merou
    Member
    quote Veerkracht:

    Hi Mika,

    You are doing a lot of work, thanks!

    In Tedd’s list there is a:
    20 x 1 Buna 90 baffle
    I think this should be the
    19 х 2 – 1 pcs (permanent compensator seal)
    in your list?

    Regards, Robert.

    Hi Robert Thanks,
    yes for the 19 х 2 – 1 pcs (permanent compensator seal)

    I find a new site adress for O’ring but sorry it’s French.
    I test it beceause I’ve got some problem with 2 O’ring on my ill Pompe.

    the adress :
    http://www.oring.fr/?gclid=CIrEsKSYsb4CFdLHtAodazoArg

    Put the size of the O’ring you need :

    Select the categori : ex : duro 70, 80, or 85

    The price :

    The choice of the categories for PCP (Air comprimé)

    The new O’ring package :

    The new update ( I use the original O’ring since 6 years, good performance, the ill pompe is like a TANK)

    Test of the New O’rings 200 BARS. OK

    Thanks.

    Best regards,

    MIKA

    #236672

    toshik
    Member

    Up for people, looking for those sizes.

    #236673

    gringoloco38
    Participant

    :8: :8: :8:

Viewing 15 posts - 16 through 30 (of 65 total)

You must be logged in to reply to this topic.

Skip to toolbar