Taipan Laminate airgunUragans airgun

Complete Oring List

Home Forums BullPups EdGun Complete Oring List

This topic contains 64 replies, has 26 voices, and was last updated by  airbrained 1 year, 1 month ago.

Viewing 15 posts - 1 through 15 (of 65 total)
  • Author
    Posts
  • #9712

    eddieirvine
    Member

    Anyone have a complete oring assembly for the Edgun Matador? I am sure things will last for some time I have replaced the bolt orings when I got my gun but just curious if there is a list someplace of all of them thanks Eddie

    #119462

    mamcrackin
    Member
    quote eddieirvine:

    Anyone have a complete oring assembly for the Edgun Matador? I am sure things will last for some time I have replaced the bolt orings when I got my gun but just curious if there is a list someplace of all of them thanks Eddie

    eddie, there are only 3 (maybe 4) inside the gun that are all the same
    size. 2 (maybe 3) around the regulator/air valve, and 1 that seals the end cap of the air
    reservoir. Then there is one that seals the end of the barrel at the transfer
    port block. The one that seals the barrels is a either 7mmX1.5mm or a
    6.5mmX1.5mm. The others can be gotten from Tony… I think that oldgoat
    and I are using 3mmX1mm for the bolt probe… I have plenty probe and
    barrel seal orings if you need… Or you can get them cheap from McMaster
    Carr…

    #119841

    eddieirvine
    Member

    Thanks Jeff I was just curious not expecting to get into any in the valve or anything unless I have a problem, but probably won’t just was thinking about it the other day, I know quite thinking and go shoot it LOL 😆 I did replace one on my bolt it had a cut on it so I should get a few of them for spares, I think it might of been a bit dry, a dab a silcone grease does wonders for orings 😯

    #119842

    mamcrackin
    Member

    Yep… The harder orings are not so silicone needy. The hold up really well… I
    am not sure which Ed used for the .25 but I have not needed to replace them
    yet…

    #119843

    dvu0704
    Member

    It would be nice to include a few set of o-ring with the gun.

    Eddie, did you look through the manual? the o-ring sizes maybe descript in there.

    #119846

    oldgoat
    Member

    I would also like to get a complete list of the O ring sizes.

    Tony and/or Ed are you out there?

    Curious minds want to know! 😆

    #119862

    toshik
    Member

    They are as follows:
    • Ф 2,57 х 1,78 – 1 pcs (front plug filling valve)
    • Ф 3 х 1; 2.5 х 1,02 – 2 pcs (pellet probe for .22 or .177)
    • Ф 5 х 1,5 – 5 pcs (front of the regulator shaft – 1, inside the regulator – 1, bottom of the bolt assembly -1, filling probe – 2)
    • Ф 7 х 1.5 – 1 pcs (rear of the barrel seal), .177 uses Ф5х1,5)
    • Ф 8 х 1.5 – 1 pcs (rear of the regulator shaft)
    • Ф 12 х 2,5 – 1pcs (permanent compensator seal)
    • Ф 25 х 3 – 4 pcs (front and rear plugs, regulator)

    #119864

    gringoloco38
    Participant

    Hi Tony, thanks!! VERY usefull… 😆

    #119866

    mamcrackin
    Member

    Great information Tony…… Thanks… You’re again the best… 😀

    #119868

    gringoloco38
    Participant
    #119877

    hoot
    Participant
    quote toshik:

    They are as follows:
    • Ф 25 х 3 – 4 pcs (front and rear plugs, regulator)
    • Ф 2,57 х 1,78 – 1 pcs (front plug filling valve)
    • Ф 5 х 1,5 – 3 pcs (front of the regulator shaft) – 1, inside the regulator – 1, bottom of the bolt assembly -1)
    • Ф 8 х 1.5 – 1 pcs (rear of the regulator shaft)
    • Ф 7 х 1.5 – 1 pcs (rear of the barrel seal), .177 uses Ф5х1,5)
    • Ф 12 х 2,5 – 1pcs (permanent compensator seal)
    • Ф 3 х 1; 2.5 х 1,02 – 2 pcs (pellet probe for .22 or .177)
    • Ф 5 х 1,5 – 2 pcs for the filling probe

    Tony, make this simple for us. Would you be willing to sell us a complete set of O rings for the Edgun, as shown above, in a plastic bag?

    You might find substantial interest in Edgun owners!

    By the way, has the shipment of Edguns left Mother Russia yet?

    Hoot 😯

    #119889

    eddieirvine
    Member

    Thanks Tony I will copy that for future Ref. It will come in handy if I need it 😆

    And Oldgoat thank you for your message on my email your the best! thanks again Eddie

    #119916

    toshik
    Member
    quote Hoot:

    Tony, make this simple for us. Would you be willing to sell us a complete set of O rings for the Edgun, as shown above, in a plastic bag?
    You might find substantial interest in Edgun owners!
    By the way, has the shipment of Edguns left Mother Russia yet?
    Hoot 😯

    One spare kit comes with every single Edgun product. I don’t see why not.
    I’ve got .22 Lelja and Veles for sale (not reserved) right now.

    #119938

    dvu0704
    Member

    Hi Tony,

    Is the new Veles still .177 cal? Do you have any Veles .22 cal? I may buy new Veles if it available in .22 cal.

    #119952

    hoot
    Participant
    quote toshik:

    One spare kit comes with every single Edgun product. I don’t see why not.

    I’ve got .22 Lelja and Veles for sale (not reserved) right now.

    In stock and ready for shipment dude…give the man a call….$1300 bones shipped.

    Your best friend ever….

    Hoot 😯

Viewing 15 posts - 1 through 15 (of 65 total)

You must be logged in to reply to this topic.

Skip to toolbar